BSH brings you the strongest and most feature rich street performance motor mount kits available. Each component has been designed to accomplish rock solid performance while still maintaining the finesse of a daily driven street car. For optimum results this mount should be paired with the BSH Engine Mount.
Performance Features:As we are sure you’ve noticed the factory motor mounts have a ton of give in them. Our billet mounts reduce the ability of the engine to flex back by replacing the factory fluid filled mounts with street performance bushings and the billet bodies to hold them. This bushing set does a great job of limiting movement while still maintaining an acceptable level of comfort needed to be used on a daily driven street car. This both greatly enhances the fun factor and performance of the car and also removes the all too common problem of blowing out the factory mounts on your higher powered setup.
After installation you will notice the following:
Significantly reduced engine movement.
More feedback from the engine
Greatly reduced wheel hop
More defined throttle input
Smoother shifts for both DSG and Manual cars
Billet Aluminum Bodies
Two piece base with compression fit stainless steel center shaft
BSH Proprietary Street Sport Bushings
Black anodized finish
Precision cut stainless steel powder coated battery brackets
All necessary hardware
Replacement bushing for your BSH lower mounts. We use 70 Durometer rated urethane which we have found to provide an acceptable ride for your street car yet still stiff enough for track duty. We recommend you replace your bushing every 50,000 miles.
THIS IS THE FULL BIKE. WE ALSO OFFER THE FRAME, MOTOR, AND BATTERY SEPARATELY.
KirbEbike Vapour embraces everything we have learned from years of experimentation with electric bikes and, what we think is our best, most refined electric bike yet.
Vapour is based on the all new Vapour 1.0 chassis, made of high spec AL6061 T6 Aluminium alloy. This frame is a strong full suspension platform designed for maximum agility in the twists and turns ready to take on most demanding trails while remaining stiff enough to handle the incredible torque of the latest Bafang M620 mid drive motor. This motor delivers incredible torque of 160nm and power up to 1500W (more with higher power batteries!!). The Vapour is available in 2 sizes (17″ and 19″) and supports 27.5 inch wheels with boost spacing. The frame has a 66.5 degree head angle designed around 140-160mm front suspension travel. Rear suspension uses a vertically mounted 190x50mm shock providing 144mm rear arm travel. What makes the Vapour chassis unique? firstly it’s clever battery mounting system which blends the battery to the frame without compromising strength or requiring a proprietary battery! With this kind of power and handling you will find yourself soaring uphill past big brand eMTB’s costing 3 times They won’t catch you on this one!
Finished in a stunning matt black allows for easy customisation or that stealth look.
Buy with confidence! Frame comes with a full 5 year warranty, electronics have a 1 year warranty.
Email for availability.
Frame: 6061 Alloy aluminum, Matt Black
Tyres: 27.5*2.6 Schwalbe Smart Sam
Rims: MD35 Boost double wall rim
Front Fork: ROCKSHOX YARI
Front brake: TEKTRO 180mm Hydraulic disc brake
Rear Brake: TEKTRO 180mm Hydraulic disc brake
Spokes: 13g stainless steel
Derailleur: shimano 10 speed m6000
Rear Shock: X-Fusion o2
Handle Bar: Aluminium Alloy
Seat post: Aluminium Alloy
Saddle: Velo VL-1589
Stem: Aluminium Alloy
Brake Lever: TEKTRO Aluminium
Chain: KMC Rust resistant chain
Chainring: STEEL 42T
Motor: Bafang M620 MID-DRIVE 48V/1000W with Colour LCD
Battery: 48V/14Ah LG MJ1 battery
PAS: Torque + speed sensor
Controller: 48V Intelligent brushless controller
Display: Bafang LCD Performance
Top Speed: below 37 MPH
Range: >31 Miles
Max Load: 220lbs
Weight: 51 lbs
48V 14Ah high power LG MJ1 battery
Plastic, carbon fibre look finish with blue LED fuel gauge
Vapour battery mounting system for Vapour frame (lockable)
On/off switch on battery
2A Mains Charger
Now it is possible to build your own eMTB to rival the big brand eMTB’s. We are not talking just another high power ebike here, this is a real eMTB with proper geometry, designed for the trails and advanced riding.
KirbEbike Vapour embraces everything we have learnt from years of experimentation with electric bikes and we think is our best, most refined electric bike yet.
We have made our frame available for serious builders who want to put together an eMTB to their exact specification. The all new Vapour 1.0 chassis, made of high spec AL6061 T6 Aluminium alloy is a strong full suspension platform designed for maximum agility in the twists and turns of the most demanding trails whilst remaining stiff enough to handle the incredible torque of the M620 motor. Vapour is available in 2 sizes and supports 27.5 inch wheels. The frame has a 66.5 degree head angle designed around 140-160mm front suspension travel. Rear suspension uses a vertically mounted 190x50mm shock providing 144mmm rear arm travel.
What makes the Vapour chassis unique? firstly it’s clever battery mounting system which blends the battery to the frame without compromising strength or requiring a proprietary battery, in fact we will also be making the battery case available for the battery self builders out there! Secondly the motor mount is designed exclusively to fit the readily available M620 powerhouse from Bafang. This motor delivers incredible torque of 160nm and power up to 1500W (more with higher power batteries!!). This kind of power will have you soaring uphill past big brand eMTB’s costing 3 times as much whilst still having the maneuverability of a proper eMTB in the turns! They wont catch you on this one!
Vapour is available in 2 frame sizes; 17 and 19 inches. The finish is in stunning matt black to allow for customisation or that stealth look.